Composite Silicate Plate Selection Guide: Identity, Standards and Temperature Limits
Engineering selection guide for composite silicate board: confirm material identity, size on λ at the converged mean temperature, and apply temperature, CUI and fire gates before writing a spec.
Quick answer: Composite silicate plate is a Chinese trade family of board-form inorganic insulation — not calcium silicate, not aluminum-silicate fiber and not aerogel. Select it by first proving material identity, then by checking λ at the converged mean insulation temperature, then by temperature, mechanical, moisture and CUI gates. Most specification failures come from comparing a room-temperature λ against a hot-service calculation, or from trusting a "600–800 °C" claim without a form-specific type test.
Key Takeaways
- Material identity is the first gate. "Composite silicate" (Chinese trade name, JC/T 990 family) is a different family from calcium silicate (GB/T 10699), aluminum-silicate/refractory fiber (GB/T 16400) and aerogel blanket (GB/T 34336). Require the exact Chinese name, form, chemistry, standard and a type-test report for the supplied form before comparing any number.
- Size on the converged mean temperature, not room-temperature λ. A worked DN200 steam pipe at 250 °C shows the trap: an initial 150 °C mean estimate gives about 89.5 mm, but iterating to the converged mean of about 197 °C raises λ to about 0.0786 W/(m·K) and the required thickness to about 107 mm.
- Temperature claims need form-specific evidence. The only directly documented family limit found is 350 °C for the related coating grade (GB/T 17371); board claims of 600–800 °C exist but are not backed by a verified unified national board-grade limit. Treat 500 °C as a project-test threshold, not a default.
- A-class material does not equal an assembly fire rating. GB 8624 classifies the material; the system rating also depends on jacket, adhesive, fixings, joints and penetration detail. GB 55037-2022 is fully mandatory from 1 June 2023 and overrides conflicting older provisions.
- Specify performance, not a trade name. Require λ at the stated mean temperature and test density, compressive stress at a defined strain, water-extract pH/chloride for stainless service, linear shrinkage and a traceable report at the supplied form and thickness.
1. Scope and mandatory disambiguation
This guide covers rigid and semi-rigid board-form composite silicate insulation, plus the related paste, coating, mat and flexible forms of the same family where those forms change board selection. It deliberately excludes calcium silicate board, aluminum-silicate/ceramic fiber, aerogel blanket, rock or glass wool and organic foam — those are different chemistries and design choices.
Composite silicate plate is a broad Chinese trade description rather than a single controlled formula. Typical board systems use layered silicate minerals such as attapulgite/palygorskite or sepiolite, expanded perlite or vermiculite, binders, reinforcing fibre and fillers. Attapulgite is a hydrated magnesium-aluminum silicate with a rod-like structure, which explains the "magnesium-aluminum silicate" trade name; that mineral identity is not proof of a temperature ceiling or mechanical strength. The binder and fibre decide whether the product is inorganic and non-combustible, or contains an organic component that can char, shrink and emit volatiles.
| Claimed or apparent name | Actual material family | Typical standard | Does not replace |
|---|---|---|---|
| Composite silicate board / composite silicate insulation board / magnesium-aluminum silicate insulation material | Composite silicate / aluminum-magnesium silicate board, paste or mat family | JC/T 990-2006 identified for the board family; coating separately standardised | Calcium silicate; ceramic fiber; aerogel |
| Silicate composite thermal insulating coating / composite silicate paste | Silicate composite coating or paste, wet-applied | GB/T 17371-2008 | Board product standard |
| Calcium silicate board / calcium silicate | CaO–SiO2–fibre–water product, rigid block or pipe | GB/T 10699 (e.g. 2015) | Composite silicate board |
| Aluminum-silicate wool / ceramic fiber | Al2O3–SiO2 fiber blanket or board | GB/T 16400 (e.g. 2023) | Composite silicate board |
| Aerogel composite insulation product / aerogel blanket | Silica aerogel composite, usually flexible blanket | GB/T 34336-2017 | Composite silicate board |
| Rock wool / slag wool, glass wool, PU/PIR, phenolic foam | Mineral wool, foam products | Separate GB/T product standards | Composite silicate board |
The disambiguation rule is stricter than matching trade names. "Aluminum silicate" may mean ceramic fiber; "calcium silicate" means calcium silicate; "magnesium-aluminum silicate" normally means the layered-clay composite family. A submittal showing ASTM C533 is evidence for calcium silicate, not composite silicate. For the material family this guide covers, see our composite silicate plate product page; for the genuinely different chemistry, see the calcium silicate insulation buyer's guide and the calsil vs ceramic fiber refractory board comparison.
2. Composition and manufacturing variants
The controlling ceiling is usually the organic content, binder decomposition or fibre stability — not the nominal clay mineral. The layered silicate supplies low density and high-temperature mineral content; perlite, vermiculite and air pores supply much of the thermal resistance. The forming method (wet slurry cast board, compression-moulded block, oven drying, or fibre added for mat) controls density, strength, shrinkage and moisture behaviour. Obtain a formula-class declaration: inorganic mineral binder only, organic latex/acrylic/thermoset resin, and inorganic or organic fibre. The same trade name can exist in all three variants.
Organic binders improve green strength and handling but create a real maximum-service-temperature question: above the decomposition range they can char, stiffen, shrink and lose cohesion. An inorganic binder can still carry soluble salts or high pH. Fibre reinforcement raises flexural handling strength but the fibre type affects high-temperature linear change, dust release and refractory performance. A "non-combustible" declaration must therefore be tied to the tested product form and thickness, not inferred from the word "inorganic" on a datasheet.
Hydrophobic treatment improves spray resistance, but a water-spray test is not proof of zero capillary uptake, zero vapour transmission or immersion suitability. The water jet in GB/T 10299 strikes a specimen surface; it does not test long-term standing water, seawater spray, freeze-thaw or water trapped at a metal interface. A board can show a high hydrophobicity rating and still allow CUI if cut edges, fastener penetrations or joints lack a compatible sealed jacket.
If the same supplier proposes board, paste and joint compound from one "composite silicate" system, the assembly — not the board alone — must satisfy chloride, fluoride, pH, leaching and stainless-steel compatibility requirements.
3. Performance indices and what to demand
Board product data are fragmented and market claims are not standardised, so specify by performance. Values marked "typical commercial, not normative" below are collected enquiry ranges, not guaranteed design values.
| Property | Engineering meaning | Typical commercial range / verified limit | Test method | Measurement pitfall |
|---|---|---|---|---|
| Thermal conductivity λ | Controls thickness and heat loss; rises with mean temperature | Datasheets often claim 0.035–0.065 W/(m·K) at room or unspecified temperature — not normative | GB/T 10294, GB/T 10295, ISO 8301/8302, ASTM C177/C518/C335 | Comparing a 25 °C value with a 200 °C calculation; ignoring thickness and conditioning |
| Maximum service temperature | Temperature with acceptable shrinkage and property change | 350 °C documented for the coating grade; 600 °C and 800 °C board claims exist but are not a verified unified board-grade limit | GB/T 17430, ISO 8142, ASTM C411/C447 | Treating the stated maximum service temperature as continuous service temperature |
| Bulk density | Governs mass, load, space, λ and strength | Common listings 120–260 kg/m³ — not normative | GB/T 5486, GB/T 20313, ASTM C303 | Comparing shipping bulk density with tested apparent density |
| Compressive behaviour | Hanger, saddle and walk-on resistance | Claims of 100–600 kPa, often at undefined strain — not normative | GB/T 5486, ISO 29469, ASTM C165 | Using peak load when the project needs 10% deformation stress |
| Flexural behaviour | Board handling and long unsupported spans | Typical claims 150–400 kPa — not normative | Product-specific mechanical test | Reporting break load without span, width and thickness |
| Water absorption | Saturated-weight gain and λ drift | "volume water absorption" claims of 1–5% — not normative | GB/T 5486, ISO 2896, ASTM C240/C302 | Short immersion does not reproduce long-term CUI |
| Hydrophobicity | Water repelled under a specified spray | Claims of 98–99% — not normative | GB/T 10299 | Treating spray repellence as immersion or vapour-barrier proof |
| Linear change after heating | Permanent gap and hot-face stability | Request at declared max temperature and hold time | GB/T 5486, ASTM C356/C210 | Reporting change without atmosphere or hold time |
| Combustibility | Material fire classification | Claims of A / A1 / A2 — not normative | GB 8624, GB/T 5464, GB/T 14402, EN 13501-1, ISO 1182, ASTM E136 | Confusing material class A with an assembly rating |
| pH and soluble chloride/fluoride/sulfate | CUI and austenitic stainless SCC | Project-specific limits; require water-extract pH and ionic analysis | GB/T 17393, JC/T 618, ASTM C795/C871/C692 | Accepting "chloride-free" without extraction method and detection limit |
| Fibre/dust and asbestos | Fabrication hygiene and exposure | Asbestos-free alone is insufficient | GB/T 23263, GBZ 2.1 | Substituting "no asbestos" for mineral-fibre and silica dust control |
Moisture and compression must be specified as field conditions, not laboratory ideals. Water raises both conductivity and load; a wet board's λ can exceed the dry declared value by an amount that depends on saturation and temperature. Compression raises local density but can damage pore structure, open joints and reduce thickness — the correct acceptance item is post-compression thickness and residual λ, not "higher density is better." Under hangers, shoes and saddles, require compressive stress at a defined strain and calculate bearing pressure from the support reaction divided by the real contact area.
4. Standards, codes and fire compliance
There is no single uniformly applied national product standard for every "composite silicate board," and that gap is a specification risk. JC/T 990-2006 is identified in the Chinese standard literature as a composite-silicate insulation product standard, but its full current limit table is not open-access. GB/T 17371-2008 governs the coating family, not boards. When a board is offered only to an enterprise standard, convert that standard into measurable generic-test-method requirements.
| Layer | Standard / code | Status and relevance |
|---|---|---|
| Board product | JC/T 990-2006 Composite Silicate Insulation Products | Board-family product standard; verify the current edition and obtain the full limit table before purchase |
| Coating/paste | GB/T 17371-2008 Silicate Composite Thermal Insulating Coating | Relevant when paste/coating is the same family or used as adhesive/joint filler; includes SCC- and pH-related material |
| Generic thermal | GB/T 10294, GB/T 10295, GB/T 10296 | Steady-state thermal resistance and conductivity |
| Generic mechanical/density/water | GB/T 5486, GB/T 13480, GB/T 20313 | Compression, density and water-related tests |
| Max service temperature | GB/T 17430 | Project must define temperature, time, atmosphere and acceptance change |
| Fire classification | GB 8624-2012 | Applicable design/contract edition at the time of this guide |
| Fire classification, future | GB 8624-2025 | Published, effective 1 January 2027 — do not substitute it on contracts controlled by the 2012 edition |
| Fire testing | GB/T 5464, GB/T 14402, ISO 1182, EN 13501-1, ASTM E136 | Non-combustibility and A-class basis |
| CUI / stainless corrosion | GB/T 17393-2008, JC/T 618, ASTM C795/C871/C692 | GB/T 17393 covers austenitic stainless insulation with an SCC test and water-extract pH |
| Hydrophobicity | GB/T 10299-2011 | Spray-condition water repellence only |
| Industrial design | GB 50264-2013 | Current national industrial design code, mandatory clauses |
| Construction | GB 50126-2008 | Construction code |
| Quality acceptance | GB/T 50185-2019 | Effective 1 March 2020; replaced GB 50185-2010 |
| Design guidance | GB/T 8175-2008 | Long-standing guide; a 2025 edition is reported effective 1 May 2026 — verify the contractually applicable version |
| Building fire regulation | GB 55037-2022 | Fully mandatory from 1 June 2023, overrides conflicting older provisions |
Material A-class does not equal an assembly fire rating. GB 8624 classifies the material; an assembly rating also depends on jacket, adhesive, fixings, cavity, joints and tested system. Design documents must separate (1) material reaction to fire, (2) insulation system fire performance, (3) pipe-penetration firestop and (4) escape-route or equipment-area requirements. Do not issue a blanket "Class A therefore no further fire design" statement.
Submittals must be traceable to the supplied form. A compliant report states the exact product name and form, declared and actual test density, lot number, specimen dimensions and conditioning, mean temperature for λ, thickness and panel configuration, hot- and cold-face temperatures, maximum-temperature hold time and acceptance criteria, compression strain definition, water absorption procedure, pH and extract chemistry, chloride/fluoride/sulfate results with detection limits, fire-test specimen and report number, lab CMA/CNAS scope and issue date. A 25-mm coupon at one mean temperature cannot prove a 100-mm board at 350 °C; a coating test cannot qualify a rigid board.
5. Selection workflow: heat loss, thickness and checks
Steady heat transfer is solved by thermal resistance, not by multiplying a room-temperature conductivity by area. For a flat wall the heat flux is q = (Th − Tc) / (δ/λ + Rext), where δ is thickness in metres, λ is conductivity at the relevant mean temperature in W/(m·K) and Rext is the external surface resistance in m²·K/W. For a pipe or cylindrical vessel, use the logarithmic mean area: Q = 2πL(Th − Tc) / [ln(r2/r1)/λ + Rext·2π/r2], with r1 the inner radius and r2 = r1 + δ the outer radius.
| Symbol | Meaning | Unit | Source |
|---|---|---|---|
| Th | Hot-face/service temperature | °C | Process data |
| Ts | Outer surface temperature | °C | Calculation or measurement |
| Ta | Ambient air temperature | °C | Project design condition |
| Tm | Mean insulation temperature | °C | Formula / (Th + Ts)/2 approximation |
| Tdp | Ambient dew point | °C | RH and Ta |
| λ | Conductivity at Tm | W/(m·K) | Manufacturer type test |
| ho | Combined convection + radiation coefficient | W/(m²·K) | Calculation or correlation |
| δ | Insulation thickness | m | Design result |
For natural convection use a horizontal-cylinder or vertical-plate correlation; for forced convection include wind speed. Radiation uses hr = εσFview(Ts⁴ − Tsurr⁴)/(Ts − Tsurr), so ho = hc + hr. A smooth oxidized-metal jacket has lower emissivity than a dull painted or wet organic jacket; a bright aluminum jacket can reduce loss but must be electrically and corrosion-compatible.
Worked example: DN200 steam pipe
Assumptions: carbon-steel pipe OD 219.1 mm, so r1 = 0.10955 m; saturated steam at 250 °C; indoor mechanical room at Ta = 25 °C; very low wind, assume ho = 9.0 W/(m²·K); target outer surface 50 °C for personnel protection; λ is a stated assumed manufacturer fit for the selected product: λ(Tm) = 0.050 + 2.40e−4·Tm + 6.00e−8·Tm³, with Tm in °C. This is not a universal composite-silicate law and not a standard equation.
- Estimate mean temperature: Tm ≈ (250 + 50)/2 = 150 °C.
- Evaluate conductivity: λ(150) = 0.0708 W/(m·K).
- Solve cylindrical conduction plus surface resistance: q = (250 − 50)/(Rcyl + Rsurf) = ho(Ts − Ta) gives an outer radius near 0.199 m, so δ ≈ 0.199 − 0.10955 ≈ 89.5 mm.
- Iterate because λ depends on Tm. The rigorous cylindrical mean temperature for r1 = 0.10955 m and r2 = 0.199 m is about 164.3 °C, not 150 °C. Recalculate λ, then thickness, then Tm until changes are negligible.
| Iteration | Mean temperature (°C) | λ at mean temperature [W/(m·K)] | Outer radius (m) | Thickness (mm) |
|---|---|---|---|---|
| 1 | 150.0 | 0.0708 | 0.1990 | 89.5 |
| 2 | 164.3 | 0.0768 | 0.2126 | 103.0 |
| 3 | 190.7 | 0.0783 | 0.2159 | 106.4 |
| 4 | 196.7 | 0.0786 | 0.2166 | 107.0 |
The engineering rule is to use the converged mean temperature, not the initial guess. With this assumed curve the final thickness is about 107 mm; select a commercial thickness equal to or greater than that, then recheck surface temperature. The exact final values depend slightly on how ho is updated for the new Ts.
Surface-temperature check is mandatory even when economic thickness is used. For a hot pipe, size for the energy/economic target then verify Ts ≤ Tlimit; accessible Chinese design guidance uses 50–60 °C for burn protection. If Ts exceeds the project limit, increase thickness or add a low-emissivity jacket. For cold surfaces, the cold-side temperature must stay above the local dew point; if it does not, add thickness, reduce air infiltration, lower jacket heat gain and/or provide a continuous vapour barrier on the correct side. A high hydrophobicity rating is not automatic proof of a vapour barrier.
Economic thickness is a present-value optimisation, not a single formula: minimise total installed plus lifetime energy cost while satisfying burn protection, condensation control, space/weight, support load, fire classification and maximum service temperature. If the economic minimum is thinner than the burn-protection thickness, select the thicker value; if it is thicker than temperature or weight allows, revise the material family. Include substitution, shutdown replacement and CUI repair costs for coastal or high-humidity service — these can outweigh small first-cost differences.
6. Selection matrix by temperature tier and equipment form
The matrix is a decision aid, not a certification. "Recommended" means the family can be appropriate after meeting the listed governing properties; "Conditional" means it must be justified by tests and system design.
| Temperature tier / service | Pipes and fittings | Vessels, tanks, large walls | Furnace/duct, cyclic or irregular | Outdoor / coastal / CUI risk | Verdict |
|---|---|---|---|---|---|
| Chilled / anti-condensation, roughly ≤10 °C | Conditional | Conditional | Usually not recommended | Usually not recommended | Moisture, vapour drive and absorption dominate |
| ≤200 °C: HVAC, DH, hot water, LP steam | Recommended for straight pipe; segmented board for fittings | Recommended | Recommended where board can be shaped or paste fills voids | Conditional | Require λ at mean temperature, hydrophobicity and joint jacket |
| 200–350 °C: medium process heat | Recommended if product test proves the mean temperature | Recommended | Recommended where low load and formability matter | Conditional | Use tested λ at 200–350 °C mean temperature; get shrinkage data |
| 350–500 °C: high heat | Conditional | Conditional | Conditional | Conditional | Direct documentary support found is 350 °C for the coating family; require a product-specific max-temperature test |
| 500–600 °C | Conditional, only with tested inorganic formulation | Conditional | Usually ceramic-fiber or refractory territory | Not recommended | Treat 600 °C as an upper candidate, not a default |
| Above 600 °C / severe cycling | Generally not recommended for ordinary board | Conditional for low-load passive backup | Often use refractory/ceramic-fiber systems | Not recommended | 800 °C claims do not create a verified national board grade |
| Equipment/form concern | Board selection rule | Governing property |
|---|---|---|
| Straight pipe | Segmented board lagging for repeatable thickness and lower field variability | λ at mean temperature; segment fit; support load |
| Elbows, tees, valves, flanges | Pre-formed removable covers or compatible mat/paste inserts; rigid board alone creates joints | Thermal cycling, removable geometry, jacket sealing |
| Vertical vessel | Support rings/saddles carry board weight; tall boards need anti-settlement design | Density, compressive strength, joints, moisture |
| Horizontal vessel/tank | Sliding/expansion allowance at saddles and longitudinal joints | Linear change, creep, thermal movement |
| Large flat wall | Large boards can be efficient; check wind load and support span | Flexural strength, fasteners, external resistance |
| Small-diameter pipe | Relative thickness and curvature make board joints disproportionate; flexible mat may be better | λ, curvature fit, vapour sealing |
| Outdoor | Sealed jacket, drainage and UV/weather resistance are mandatory | Hydrophobicity, absorption, jacket system |
| Buried or high humidity | Conventional rigid silicate board is normally conditional unless fully encapsulated and proven | Capillary uptake, permeability, CUI, freeze-thaw |
| Coastal chloride | Even a low-chloride board faces external CUI drive | Chloride content, pH, sealed system |
| Vibration | Soft or semi-rigid mat reduces fatigue and cracking | Flexibility, compressive creep, fatigue |
| Walkable surface | Only boards with tested load capacity and a traffic surface | Compressive stress at defined strain, wear surface |
| Food/pharma/clean area | Low dust, low odour, cleanable sealed jacket, extractable-chemical data | Fibre/dust, VOC, pH, cleanability |
| Fire-rated penetration | Material A-class is not sufficient | Tested assembly/system firestop |
For form and terminology choices around flat stock, see insulation board and panel forms and the board density, thickness and λ spec guide.
7. Decision tree and go/no-go checklist
First reject the project if temperature or chemistry is wrong; then optimise thickness.
- Identity gate: Is the submittal for the composite silicate board family, not calcium silicate, ceramic fiber or aerogel? Is the exact standard shown?
- Temperature gate: Is declared continuous-service temperature above the calculated hot-face temperature, with margin and duration?
- λ gate: Is λ supplied at the calculated mean temperature, specimen thickness and conditioning?
- Mechanical gate: Does compressive behaviour at the specified strain exceed actual bearing pressure at hangers, shoes and saddles?
- CUI/metal gate: For austenitic stainless, is there a water-extract chloride/fluoride/sulfate/pH result and a stainless compatibility test?
- Moisture gate: For cold, buried, coastal or high-humidity duty, is there a tested vapour-barrier and jacket system — not only a hydrophobicity rating?
- Fire gate: Does the material classification match the project, and has the assembly/firestop been separately addressed?
- Dimensional gate: Are linear change, shrinkage and thermal movement compatible with joints, supports and removable covers?
- Lifecycle gate: Can damaged boards be replaced without dismantling the whole system?
| No. | Question | Go | No-go / conditional |
|---|---|---|---|
| 1 | Standard is JC/T 990 family or a declared, obtainable standard | Yes | An unknown enterprise standard with no full performance specification |
| 2 | Form, density and thickness in report match supplied product | Yes | Coating tested as board, or board as coating |
| 3 | λ reported at mean temperature, not only room temperature | Yes | Room-temperature value used for hot design |
| 4 | Max service temperature has test time, atmosphere and acceptance criteria | Yes | Only a marketing temperature-resistance number |
| 5 | Compressive stress at defined strain exceeds support bearing stress | Yes | Indeterminate load capacity |
| 6 | Austenitic stainless: extract chemistry and SCC test supplied | Yes | "Chloride-free" claim without method |
| 7 | Hydrophobicity and immersion/absorption addressed separately | Yes | Spray test used as immersion proof |
| 8 | Linear change after heat and drying shrinkage reported | Yes | No shrinkage data for hot cyclic service |
| 9 | Fire report identifies specimen and A/A1/A2 class | Yes | Generic A-level sticker only |
| 10 | Assembly/system fire rating addressed for penetrations and enclosures | Yes | Material class assumed to be system rating |
| 11 | For cold duty, dew-point check and vapour-barrier design included | Yes | Anti-condensation thickness by rule of thumb |
| 12 | For hot duty, surface-temperature limit checked after iteration | Yes | Only economic thickness used |
| 13 | Thickness, weight and space constraints are met | Yes | Excessive weight or support conflict |
| 14 | Removable covers or compatible flexible form available for valves/flanges | Yes | Rigid board sealed over inaccessible items |
| 15 | Lab CMA/CNAS scope includes each claimed test | Yes | Out-of-scope report relied upon |
8. Procurement specification template
Specify the result, not a brand. Insert these fields into the purchase specification and require a completed, signed datasheet with evidence.
| Field | Unit | Test method | Acceptance limit / evidence |
|---|---|---|---|
| Exact product name and trade form (declared by the supplier) | — | Identity declaration | Composite silicate board / magnesium-aluminum silicate board, etc.; lot and formulation revision |
| Applicable product standard | — | — | JC/T 990 family or declared enterprise standard; obtain full limit table |
| Nominal thickness | mm | Caliper, GB/T 5486 family | State tolerance and conditioning |
| Length × width | mm | Dimensional check | State tolerance |
| Declared and test density | kg/m³ | GB/T 5486 / GB/T 20313 | Test density linked to each thermal/mechanical test |
| λ at Tm = ___ °C | W/(m·K) | GB/T 10294 or GB/T 10295 | Project limit; report hot/cold face, mean temperature and thickness |
| Continuous and maximum service temperature | °C | Project protocol / GB/T 17430 | Exceed hot-face with margin; state atmosphere and hold time |
| Linear shrinkage / reheat change at ___ °C / ___ h | % | GB/T 5486 | Project limit |
| Compressive stress at ___ % strain | kPa | GB/T 5486 / ISO 29469 | Must exceed calculated bearing pressure |
| Water absorption | vol% or mass% | GB/T 5486 / ISO 2896 | State method and immersion time |
| Hydrophobicity rating | % | GB/T 10299 | State surface preparation and result |
| Water-vapour transmission | g/(m²·d) or ng/(Pa·s·m) | GB/T 17146 / ISO 12572 | Correct side of vapour barrier identified |
| pH of water extract | — | GB/T 17393 appendix | Project limit |
| Water-soluble chloride / fluoride / sulfate | mg/kg | GB/T 17393 / JC/T 618 / project method | Detection limit and extraction procedure required |
| Austenitic-SST stress-corrosion test | Pass/fail | GB/T 17393 / ASTM C795 | Report, alloy and exposure conditions |
| Combustibility / fire class | A1/A2/B1 etc. | GB 8624 / GB/T 5464 / GB/T 14402 | Product report and applicable version |
| Asbestos and other fibre release | mass% / mg/m³ | GB/T 23263 / hygiene method | State detection limit |
| Binder type | Organic / inorganic | Formula declaration | Changes temperature and VOC assessment |
| Jacket/fixing compatibility | — | System test | No galvanic, chemical or thermal incompatibility |
| Ageing / thermal cycling retention | % | Project protocol | Required for intermittent service |
9. Replacement boundaries and common errors
Composite silicate board is a formable, often low-cost inorganic option, but it is not the automatic substitute for calcium silicate, ceramic fiber, aerogel or foam.
| Alternative | Choose it when | Do not choose it when | Key comparison |
|---|---|---|---|
| Calcium silicate (GB/T 10699) | Rigid high-temperature block/pipe, load and machining matter | Irregular geometry needs paste/mat form | Higher established temperature and structural identity |
| Rock/glass wool | Conformability, large-area filling and cycling matter | Rigid board, low dust and a sealed jacket are required | Fibre versus rigid-board behaviour |
| Ceramic/aluminum-silicate fiber (GB/T 16400) | Higher hot-face temperature and thermal shock dominate | 600 °C composite-silicate claim is unverified, or rigidity is needed | True high-temperature chemistry and fibre health controls |
| Microporous/aerogel (GB/T 34336) | Space is tight and thickness reduction justifies cost | Budget, abrasion or jacket integrity cannot be managed | Low λ and high-value thickness reduction |
| PU/PIR/phenolic foam | Low-temperature efficiency and vapour control dominate | Surface temperature exceeds the foam rating or fire class is inadequate | Organic chemistry, temperature and fire |
Twelve recurring errors: using room-temperature λ for hot service; ignoring the mean-temperature convention; treating the stated maximum service temperature as continuous service; trusting 600–800 °C claims; ignoring chloride on austenitic stainless; assuming A-class material equals a system rating; omitting shrinkage and ageing allowance; assuming hydrophobicity controls CUI; allowing wet-installed λ drift; over-compressing under hangers; overlooking enterprise-standard-only products; and conflating material names before comparing numbers.
10. Limitations and version verification
This guide is current to 19 November 2026. Chinese standards continue to consolidate under the mandatory GB 550xx system, and building fire standards transition toward GB 8624-2025 from 1 January 2027. Before finalising a project, verify every standard number, title, year, status, local adoption and the contract's "date of design" rule on the national and industry standard platforms. Two items are version-verification priorities: GB 8175 is reported to have a 2025 edition effective 1 May 2026 (the accessible record confirms 2008 as established guidance), and GB 8624-2025 is published but not yet effective.
Most thermal values in Section 3 are market-typical rather than normative and must not be entered into a guaranteed-performance table. The full technical tables of JC/T 990-2006 and GB/T 17371-2008 were not accessible in the open research pass, so no false class limits are asserted here. The worked example uses a stated assumed λ(Tm) fit and surface coefficient; it demonstrates iteration and check order, not a guaranteed thickness for any named product. If the actual mean-temperature λ is higher, required thickness increases; if a sealed jacket changes ho or Ts, rerun the surface-temperature and condensation checks. For austenitic stainless, nuclear, LNG-adjacent, food/pharma, life-safety or fire-rated penetration service, supplement this guide with the applicable sector specification and authority review.
Sources and verification
Primary sources are Chinese ministry standard announcements and published standard records: GB 50264-2013, GB 50126-2008, GB/T 50185-2019, GB 55037-2022 and GB 8624-2012/2025 via the Ministry of Housing and Urban-Rural Development; JC/T 990-2006 and GB/T 17371-2008 in standard literature lists; GB/T 17393-2008 for austenitic stainless insulation; GB/T 10299-2011 for hydrophobicity; and GB/T 8175-2008 with the reported 2025 edition. International standards (ASTM C533/C795/C871/C692, ISO 8301/8302/1182, EN 13501-1) are listed as comparators, not as approvals of a Chinese composite-silicate product unless a declared equivalent relationship and scope are demonstrated.
Frequently asked
Is composite silicate plate the same as calcium silicate board?
No. Composite silicate plate belongs to the composite silicate / magnesium-aluminum silicate family, typically associated with JC/T 990-2006. Calcium silicate board is a CaO–SiO2–fibre product under GB/T 10699 (ASTM C533 is evidence for calcium silicate, not composite silicate). Aluminum-silicate fiber under GB/T 16400 and aerogel under GB/T 34336 are separate families. Require the exact Chinese product name, standard and a type-test report for the supplied form before comparing data.
What is the maximum service temperature of composite silicate board?
It depends on binder and fibre, and the marketing number is not a design value. The directly documented family limit found is 350 °C for the related coating grade (GB/T 17371). Board claims of 600 °C and 800 °C exist but are not backed by a verified unified national board-grade limit. For an enterprise-standard board, treat 500 °C as a project-test threshold with a defined hold time and acceptance criteria, and reserve higher claims for specially qualified inorganic formulations.
Can I use room-temperature thermal conductivity for a hot pipe?
No. λ rises with mean insulation temperature. In the DN200 / 250 °C worked example, an initial 150 °C mean estimate gives about 89.5 mm, but iterating to the converged mean of about 197 °C raises λ to about 0.0786 W/(m·K) and the required thickness to about 107 mm. Require λ at the calculated mean temperature, specimen thickness and conditioning, then recheck surface temperature.
Does an A1 material classification mean the insulation system is fire-rated?
No. GB 8624 classifies the material; a system rating also depends on jacket, adhesive, fixings, cavity, joints and penetration detail. Separate material reaction to fire, insulation system fire performance, pipe-penetration firestop, and escape-route or equipment-area requirements. GB 55037-2022 is fully mandatory from 1 June 2023 and overrides conflicting older provisions.
Is composite silicate board suitable for stainless steel piping?
Only conditionally. Alkalinity and water-soluble chloride, fluoride and sulfate can drive chloride stress-corrosion cracking on austenitic stainless. Require water-extract pH and ionic analysis plus a compatibility test to GB/T 17393 or ASTM C795/C692, with extraction method and detection limits. A generic "chloride-free" statement without a method is not sufficient, and a sealed jacket must protect cut edges and joints.
How do I select thickness for a hot steam pipe?
Solve steady conduction with the cylindrical logarithmic mean area and the external surface resistance, using λ at the mean insulation temperature. Iterate mean temperature and λ to convergence, then select a commercial thickness equal to or greater than the result and verify the outer surface temperature against the project limit (commonly 50–60 °C for burn protection). If the economic optimum is thinner than the burn-protection thickness, use the thicker value.
Can composite silicate board replace ceramic fiber or aerogel?
Only within its evidence envelope. Choose ceramic fiber (GB/T 16400) when hot-face temperature and thermal shock dominate, and aerogel (GB/T 34336) when space is tight and thickness reduction justifies cost. Composite silicate board fits moderate-temperature inorganic board duty or a formable paste/mat family. Do not assume its 600–800 °C claims without product-specific tests, and check CUI, shrinkage and jacket design before substituting.
Request a quote
Interested in our insulation solutions? Send us your requirements and our team responds within one business day.